OC rampage extreme+e8500 @liquido

[rampageXtreme]

Ciao a tutti allora premetto che ho:

Rampage extreme
ddr3 corsair xms3 1333 9-9-9-24 1.60v + raffreddamento ram
e8500 @liquido + chipset@liquido cn radiatore biventola
ali coolermaster m850 modulare
crossfire di 2 hd4870 2x1gb con dissipatore vapor-x

per ora volevo qualche aggiustamento qui da qualche esperto, magari qualcuno mi dice se va bene o no..

Ai Overclock Tuner: manual
Oc from cpu level: Auto
Oc from memory level: Auto
FSB frequency: 400
Cpu Ratio setting: 9
Cpu clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North bridge: Auto
PCIE frequency: 100
Dram Frequency: 1600
Dram Command Rate: 1T
Dram timing control: Auto

Cas Latency: Auto
Ras to Cas Delay:Auto
Ras pre Time: Auto
Ras Act Time: Auto
Ras to Ras Delay: Auto
Ref Cycle Time: Auto
Write Recovery Time Auto
Read to Pre Time: Auto

Read to Write Delay (SD): Auto
Write to Read Delay(S): Auto
Write to Read Delay(D): Auto
Read to Read Delay (S): Auto
Read to Read Delay (D): Auto
Write to Write Delay(S): Auto
Write to Write Delay(D): Auto
Write to Pre Delay: Auto
Read to Pre Delay: Auto
Pre to Pre Delay: Auto
All Pre to Act Delay: Auto
All Pre to REF Delay: Auto

Dram Static Read control: Disabled
Dram Dynamic Write control: Disabled
Dram Skew Control
Ai Clock Twister: Auto
Ai Transaction Booster: Auto
EPU II Phase control: Auto

Cpu voltage: Auto
Load Line Calibration: Enabled
CPU PLL Voltage: Auto
FSB Termination Voltage: Auto
CPU GTLVref(0): Auto
CPU GTLVref(1): Auto
CPU GTLVref(2): Auto
CPU GTLVref(3): Auto
NB GTLVref: 10mv
North Bridge voltage: Auto
Dram Voltage: Auto
NB DDR Vref: 25mv
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5v: Auto
South Bridge 1.05v: Auto

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Configure Advanced CPU setting

Cpu ratio setting: *
C1E support: Disabled
CPU TM function: Disabled
Max CPUID value limit: Disabled
Vanderpool Technology: Disabled
Execute Disable bit: Enabled
Core Multi-Processing: Enabled



tengo a precisare che non ho voglia di strafare.... mi serve DAILY USE

[italian soldier]

Io proverei con:

Ai Overclock Tuner: manual
FSB frequency: 500
Cpu Ratio setting: 9
PCIE frequency: 100
Dram Frequency: 1600
Dram Command Rate: 2T

Cpu voltage: 1.45

E poi abbasserei piano piano il vcore. Adesso a quanto ti setta il vcore? Che bios hai sulla scheda madre?

[rampageXtreme]

grazie per la risp!
ho il bios 1003
pci frequency non dovrebbe essere 101?
ti allego uno screen

[MARCO74]

Ciao prova con questi settaggi per i 4300MHz che per un E8500 sono più che ottimi

Cpu voltage: 1.42v
Ai Overclock Tuner: manual
Oc from cpu level: Auto
Oc from memory level: Auto
FSB frequency: 478
Cpu Ratio setting: 9
Cpu clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North bridge: 333
PCIE frequency: 101
Dram Frequency: 1600
Dram Command Rate: 1T
Dram timing control: manual

Cas Latency: 7
Ras to Cas Delay:7
Ras pre Time: 7
Ras Act Time: 21
Ras to Ras Delay: 5
Ref Cycle Time: 88
Write Recovery Time Auto
Read to Pre Time: Auto

Cpu voltage: Auto
Load Line Calibration: Enabled
CPU PLL Voltage: 1510
FSB Termination Voltage: 1100
CPU GTLVref(0): Auto
CPU GTLVref(1): Auto
CPU GTLVref(2): Auto
CPU GTLVref(3): Auto
NB GTLVref: 10mv
North Bridge voltage: 1,35v
Dram Voltage: Auto
NB DDR Vref: 25mv
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5v: Auto
South Bridge 1.05v: Auto

[rampageXtreme]

mmm volevo fare delle prove, mi dite come si usa intel burn test?
dopo che l'ho lanciato mi dice :

your pc has filed linpack testing


come mai?
il test non part proprio...

[MARCO74]

per i test di stabilità io personalmente gioco per un paio di ore a un gioco bello tosto se il pc va sei più che stabile in alternativa
puoi usare prime 95 o orthos che sono simili