Asus Rampage Extreme "Official Thread"

[gullo92]

instabile cn moltiplicatore 8.5 cn orthos mi e durato 3 minuti e si e riavviato il pc. ade vi faccio sapere se va bn cn othos cn multi 7.5.

[lukas69]

Hai giocato e non ha crashato?
lascia perdere orthos non conta
devi vedere nell'uso quotidiano
comunque alza un altro poco vcore a 1,45
e vedi

[gullo92]

ho giocato e nn ha crashato adesso sto facendo il test di othos cn le impostazioni di prima ovvero prima ho quasi fatto una mezzora di test
Ai Overclock Tuner: manualOc from cpu level up: Auto
FSB frequency: 450
Cpu Ratio setting: 7.5
Cpu clock Skew: 300
NB Clock Skew: Auto
FSB Strap to North bridge: Auto
PCIE frequency: 101
Dram Frequency: 1800 mhz
Dram Command Rate: 2n
Dram timing control: Auto

Cas Latency: 7
Ras to Cas Delay: 7
Ras pre Time: 7
Ras Act Time: 21
Ras to Ras Delay: Auto
Ref Cycle Time: Auto
Write Recovery Time Auto
Read to Pre Time: Auto

Read to Write Delay (SD): Auto
Write to Read Delay(S): Auto
Write to Read Delay(D): Auto
Read to Read Delay (S): Auto
Read to Read Delay (D): Auto
Write to Write Delay(S): Auto
Write to Write Delay(D): Auto
Write to Pre Delay: Auto
Read to Pre Delay: Auto
Pre to Pre Delay: Auto
All Pre to Act Delay: Auto
All Pre to REF Delay: Auto

Dram Static Read control: Disabled
Dram Dynamic Write control: Disabled
Dram Skew Control
Ai Clock Twister: Auto
Ai Transaction Booster: Manual
Common Performance level= 9
EPU II Phase control: Auto

Cpu voltage: 1.4
Load Line Calibration: Disabled
CPU PLL Voltage: 1.55
FSB Termination Voltage: 1.27
CPU GTLVref(0): -40
CPU GTLVref(1): -40
CPU GTLVref(2): -40
CPU GTLVref(3): -40
NB GTLVref: +10mv
North Bridge voltage: 1.55V
Dram Voltage: Il voltaggio di targa delle tue ram o max 2.02V
NB DDR Vref: +25mv
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: +12.5v
South Bridge 1.5v: Auto
South Bridge 1.05v: Auto

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Configure Advanced CPU setting

Cpu ratio setting: 7.5
C1E support: Disabled
CPU TM function: Disabled
Max CPUID value limit: Disabled
Vanderpool Technology: Disabled
Execute Disable bit: disable
Core Multi-Processing: Enabled


cn queste impostazioni e stabile.
ade che cosa devo fare per salire ancora e stare stabile?

[gullo92]

45 minuti di orthos e tutto stabile ditemi cm devo andare avanti grazie

[lukas69]

prova moltiplicatore a 8

[gullo92]

adesso lo testo cn multi 8 cn orthos per una mezzoretta

[gullo92]

stabile cn multi 8 v riscrivo le seguenti impostazioni e vi rifaccio la solita cm posso salire ancora senza compromettere la stabilita

Ai Overclock Tuner: manual
Oc from cpu level up: Auto
FSB frequency: 450
Cpu Ratio setting: 8
Cpu clock Skew: 300
NB Clock Skew: Auto
FSB Strap to North bridge: Auto
PCIE frequency: 101
Dram Frequency: 1800 mhz
Dram Command Rate: 2n
Dram timing control: Auto

Cas Latency: 7
Ras to Cas Delay: 7
Ras pre Time: 7
Ras Act Time: 21
Ras to Ras Delay: Auto
Ref Cycle Time: Auto
Write Recovery Time Auto
Read to Pre Time: Auto

Read to Write Delay (SD): Auto
Write to Read Delay(S): Auto
Write to Read Delay(D): Auto
Read to Read Delay (S): Auto
Read to Read Delay (D): Auto
Write to Write Delay(S): Auto
Write to Write Delay(D): Auto
Write to Pre Delay: Auto
Read to Pre Delay: Auto
Pre to Pre Delay: Auto
All Pre to Act Delay: Auto
All Pre to REF Delay: Auto

Dram Static Read control: Disabled
Dram Dynamic Write control: Disabled
Dram Skew Control
Ai Clock Twister: Auto
Ai Transaction Booster: Manual
Common Performance level= 9
EPU II Phase control: Auto

Cpu voltage: 1.4
Load Line Calibration: Disabled
CPU PLL Voltage: 1.55
FSB Termination Voltage: 1.27
CPU GTLVref(0): -40
CPU GTLVref(1): -40
CPU GTLVref(2): -40
CPU GTLVref(3): -40
NB GTLVref: +10mv
North Bridge voltage: 1.55V
Dram Voltage: 2.02V
NB DDR Vref: +25mv
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: +12.5v
South Bridge 1.5v: Auto
South Bridge 1.05v: Auto

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Configure Advanced CPU setting

Cpu ratio setting: 7.5
C1E support: Disabled
CPU TM function: Disabled
Max CPUID value limit: Disabled
Vanderpool Technology: Disabled
Execute Disable bit: disable
Core Multi-Processing: Enabled

[ROBY88]

Ciao a tutti , ora ci sono anche io con questa mobo e il mio fido e8400...
Problema con queste impostazioni windows vista ultimate 64bit non si avvia , mi da questo errore :
File: windows\system32\ntoskrnl.exe
stato: 0xc0000221
Informazioni : impossibile caricare windows.Kernel danneggiato o mancante
Se metto tt a default parte ...

Ai Overclock Tuner: manual
Oc from cpu level up: Auto
FSB frequency: 500
Cpu Ratio setting: 8.0
cpu clock skew: 300
NB Clock Skew: Auto
FSB Strap to North bridge: Auto
PCIE frequency: 101
Dram Frequency: ddr3-2000 mhz
Dram Command Rate: 2n
Dram timing control: Manual

Cas Latency: 7
Ras to Cas Delay: 7
Ras pre Time: 7
Ras Act Time: 20
Ras to Ras Delay: Auto
Ref Cycle Time: 60
Write Recovery Time Auto
Read to Pre Time: Auto

Read to Write Delay (SD): Auto
Write to Read Delay(S): Auto
Write to Read Delay(D): Auto
Read to Read Delay (S): Auto
Read to Read Delay (D): Auto
Write to Write Delay(S): Auto
Write to Write Delay(D): Auto
Write to Pre Delay: Auto
Read to Pre Delay: Auto
Pre to Pre Delay: Auto
All Pre to Act Delay: Auto
All Pre to REF Delay: Auto

Dram Static Read control: Disabled
Dram Dynamic Write control: Disabled
Dram Skew Control: auto
Ai Clock Twister: Moderate
Ai Transaction Booster: Auto
Common Performance level = Auto
EPU II Phase control: Auto

Cpu voltage: 1.30
Load Line Calibration: Enable
CPU PLL Voltage: 1.50
FSB Termination Voltage: 1.27
CPU GTLVref(0): Auto
CPU GTLVref(1): Auto
CPU GTLVref(2): Auto
CPU GTLVref(3): Auto
NB GTLVref: Auto
North Bridge voltage: 1.55V
Dram Voltage: 2.0v
NB DDR Vref: +25mv
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge: Auto
South Bridge 1.05v: Auto

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Configure Advanced CPU setting

Cpu ratio setting: 8.0
C1E support: Disabled
CPU TM function: Disabled
Max CPUID value limit: Disabled
Vanderpool Technology: Disabled
Execute Disable bit: Disable
Core Multi-Processing: Enabled


Cosa devo cambiare?


PS: i timing su auto fanno uguale, le ram sono CSX DIABLO 2 * 1GB, sono su xp e fa sempre uguale non carica il sistema operativo...
Ho levato vista perchè il superpi si impallava sempre anche a default , infatti ora su xp questo funziona.....

[gullo92]

mettendo il moltiplicatore a 8 pero mentre gioko a gta iv o far cry 2 mi da a volte degli scatti lunghi frequenti nei 2 gioki mentre cn il 7.5 multi nn me li dava cm risolvo il provo se devo salire di frequenza aiutamii!!

[gullo92]

ho provato cn multi 8.5 e va benissimo e stabile cn prime95. lo testato per circa 40 minuti pero ce sempre il problema degli scatti lunghi frequenti nel gioko. ho controllato le tempo sn aposto. bisogno mettere aposto qualche impostazionne nel bios. vi ringrazio ancora per la vostra disponibilita aspetto risposte